I would like to know where to find a table with the error codes. My station after restarting and during calibration shows the code ES261. The station is blocked and I cannot advance or use it in any way.
Dez. '24
Dez. '24
I think you have cleared the gimbal calibration, you have to switch on the transmitter with sliders and gimbals in the middle position. Afterwars, you have to hold them each in the extreme end positions (left upper corner, right lower corner) until the LED does not flicker anymore, The slidders needs to be put in the end positions as well. Then you should be able to confirm the new calibration with the OK button.
BR Andreas
It's incredible but true how bad the instructions for the SX9 cockpit are. Nowhere does it say how to calibrate it. Last night, after going over and over it and trying 50 times, I managed to calibrate the transmitter. On the transmitter there is a message saying "put the sticks and the wheels in the central position and press OK" and it stays blocked with the code ES261 which I don't know what it is, but it seems like an error code. You have to press OK and that code ES261 appears and then OK it goes from blue to orange, that is when you have to move the sticks to the most extreme lateral positions in a cross, also the same with the wheels, but the wheels have to be left in the central position. During this process the central power light turns red... during the time it turns red, you have to wait for it to turn off, in this way the machine confirms that the calibration has been done for each most extreme point of the center, forming a cross and with the wheels, their most extreme point of the center, that is to say on each side of them. What is not acceptable is that when loading the transmitter vertical lines appear that do not go away. Dubious German quality.
This is a real bad comment. You are blaming a nation for your problems with a product!?!? Why are you asking for help in a german language community?
You may remember that the C3 is available since years and some 1000 users have bought it and are happy using it. I used to have one myself but never ever I have heard of an experience like you are going thru now. The manual is may not the best but it is surely better than the most. Especially the level you are currently failing on, is fairly good covered,
So, before blaming "german quality" for that trouble, you should be certain that your transmitter is not simply broken or you are just not able to read and understand how it works.
However, the way you are describing your problem, the fact that you just and simply start writing in english even though this is a german language forum, the fact that you are obviously not familiar about how to work with a forum like this and you could not even pick the correct category for your thread ... all that make me believe the problem is not your transmitter.
I guess he is Spanish, and the spanisch language is selected? However we do not know what you mean with vertical lines, maybe you simply selected the screen with the vizualisation which is showing the sliders position?
Noboady told you to perform a gimbal reset, but you were right, at your selected language there some words seems to be missing (ESxxx) is in my opinion just a placeholder for an spanish language sentese like "bring all controls to the center position".
Best regards
Hallo Andreas,
er meinte diese zwei weißen Linien die von oben nach unten gehen.
Das Bild das er gemacht hat ist blöd... weiße Linien auf weißem Grund ist immer schlecht.
Unten beim OK sieht man sie wieder.
Ich denke dass das Display defekt ist. Sender zum Multiplex Service, dann ist bald wieder gut!
Gruß macsimu
| Thema | Kategorie | Antworten | Aufrufe | Aktivität |
|---|---|---|---|---|
| Cockpit SX 9 mit Unisens | COCKPIT SX | 5 | 610 | Okt. '24 |
| Mulitiplex royal evo 9 mit pc verbinden nicht möglich! | 3 | 448 | Apr. '24 | |
| Cockpit SX12 verliert Mischereinstellungen | COCKPIT SX | 9 | 708 | 4d |
| Klappen auf drei Stufen Schalter | COCKPIT SX | 2 | 514 | Aug. '24 |
| Welche Empfänger übertragen die Empfängerspannung? | MULTIPLEX Empfänger | 8 | 631 | Apr. '24 |
