Pas de son sur switch aux2 dans multicoptere

Vicari1 2018-07-31 10:50:27 UTC #1

bonjour,
Je configure un model en multicoptere..
je sélectionne aux2 en mode de vol, et lui attribue à chaque position un son.IL l'inscrit bien dans le menu attribution des interrupteur, mais le le dis pas dans le haut parleur.

Si je configure le modèle en acro la pas de soucis tout est parfait et dis dans le haut parleur.
l'icone HP a bien été activé.

Quelle est le problème?
BUG du logiciel ou délibérément impossible pour multicopteres.

Amicalement
Raymond Vicari
Membre AAM

AndreasJ 2018-07-31 20:36:43 UTC #2

Dear Sir,

it will be difficulty to give you a correct answer, because no one here is speaking native frensh..... Please try to write you querys in english.....

If you are wondering why no sound is played, please check the sound symbol in the status menu, and select the speaker symbol, by pressing it some times, repeat this for each flight phase.

best regards
Andreas

Cher Monsieur,

il sera difficile de vous donner une réponse correcte, car personne ici ne parle francais frensh ..... S'il vous plaît essayer de vous écrire querys en anglais .....

Si vous vous demandez pourquoi aucun son n'est joué, veuillez vérifier le symbole du son dans le menu d'état, et sélectionnez le symbole du haut-parleur, en le pressant quelques fois, répétez ceci pour chaque phase de vol.

meilleures salutations
Andreas

Vicari1 2018-08-01 09:40:50 UTC #3

Dear Sir Andreas,
I made the selection in the status bar, nothing helps.
On the other hand as I said acro no problem, this is to be emphasized.
Sincerely

AndreasJ 2018-08-01 17:00:30 UTC #4

Had you assignd a switch instead of the button for Teacher Pupil \ Vario? If yes please move position

Vicari1 2018-08-02 13:45:25 UTC #5

dear sir Andrea,
No other switch is assigned to pipil / vario teatcher.
I was at my dealer and after multiple tests he also found a problem with the software.
He will, however, tomorrow refer to his multiplex representative traveler, who will do the test on another radio.
I still reprogrammed a new multicopter model today and the problem remains there.
I even found that on the switch cs / A-rot when it is ationne it says one of the messages programmed on the 2 while on this one it does not say it.
I think as a technician in electronics and automation that there is actually a problem in the software.
I am at your disposal to advance this technique is superb.
good to you
Raymond Vicari
Google Translate

AndreasJ 2018-08-02 15:11:38 UTC #6

I tried the multicopter template and found no problem.... If you have activated flight phases only an announcement of the switch assigned to a flight phase (arot is one) will done if the flight phase changes.....

So if for example phase 4 is active, this has priority,

As long phase 4 is active you could not use phase 3,2,1...

so if you move the flight phase switch for 1,2,3 you will hear therefore no sound, because its not really active... This is done because if you want announced the flight phases only the real active phases may be announced.

If you switch off flight phases you will hear all switch sounds....

Vicari1 2018-08-03 07:34:09 UTC #7

dear sir Andreas,
first thank you for your follow-up problem, but I do not understand the system of phases. In principle in multicoptere we do not know how to activate more than 3 phases according to the little, the very little information of the complement of the instructions for use. Which also says that the additional phases 4 and 5 are only for the fixed wings.
And actually in the menus of the sx 12 phases 4 and 5 are grayed out and not accesible. more if I take a new model on a new memory I assume that I am in factory configuration, so in multicopter mode only 3 phases for Aux 2. And the problem is still present.
Have a good day
Raymond Vicari

AndreasJ 2018-08-03 15:12:39 UTC #8

Please turn off flight phases , because at multicopter you will make the flight modes in the flight controller.... Then the sound will work for your needs

Vicari1 2018-08-04 07:18:58 UTC #9

Ok dear sir Andreas,
Actually by disabling the flight mode the sound is there.
It may be useful to point this out in your manual for other users and avoid a request on the forum.
Thank you for follow-up and I would communicate the info to zhype in France.
Yours truly
RV

Basiert auf Discourse, funktioniert am besten mit aktiviertem JavaScript