WINGSTABI - Sender Typ nicht auswählbar

[Orthac]

Hallo alle zusammen,
ich habe das Problem, dass ich im Multiplex Launcher keinen Sender Typ auswählen kann. Standardmäßig wird dort "Mulitplex SRXL" Angezeigt. Das Dropdownmenü ist ausgegraut. Leider ist es mir damit nicht möglich, wie in dem Video "MULTIPLEX Wingstabi Workshop FAQ" auf Youtube beschrieben, auf das PPM Summensiegnal umzustellen. Ich gehe davon aus, dass dadurch der Empfänger nicht erkannt wird und ich mein Modell nicht einlernen kann.Im Menü 1 beim Launcher steht auch: "RC Kalibrierungsfehler, Kein RC Signal". Das Wingstabi 7 System wird über USB problemlos erkannt auch habe ich alle Updates für den Launcher installiert.

Folgende Komponente besitze ich:

Komponente: Wingstabi 7
Modell: Multiplex Funray
Empfänger: FS-IA10B
Fernbedienung: Flysky FS-I6X

Ich weiß aktuell nicht wo das Problem liegt. Da ich relativ neu im Modellbau bin, würde ich mich über jeden Tipp sehr freuen. Vielen Dank im Voraus.

Lg, Daniel

[Roland2]

Servus Daniel,
hast du den Wingstabi mit Strom auch versorgt? Sonst geht da auch nichts.
Ist die aktuelle Version am Wingstabi? Lässt sich ein paar Updates machen.
Verwendest du ein Original USB Kabel.

Diese Zusatzanleitung ist auch nützlich.

https://www.multiplex-rc.de/Downloads/Multiplex/Bedienungsanleitungen/55016-bedienungsanleitung-erweitert-wingstabi--de-en-fr.pdf

Gruß Roland

[FrankS]

My Wingstabi's are all MLink but I have also set up other stablisers on different radio brands so below are a few suggestions

1) If you are setting up the model via launcher , the Wingstabi needs to be connected to the receiver and powered,with the transmitter on and connected to the receiver

2) Make sure the receiver is configured for the correct signal output, some I have used have to follow a specific procedure to change to the desired mode, this is usually shown by a changing LED colour on the receiver or some flashing sequence.

3) reading the description of the receiver the single wire output is described as IBus, I am not sure if this is supported by Wingstabi.

[Orthac]

Hallo Roland,
vielen Dank für deine Antwort.
Ich habe mal ein paar Bilder gemacht:

Das Wingstabi ist mit allen Servostecker verbunden und erhält so auch Strom. Die grüne Lampe am Wingstabi blinkt auch grün. In der Software sagt er aber, dass er das RC Signal nicht finden kann. Der Empfänger ist aber mit mit der Fernsteuerung verbunden. Als USB Kabel verwende ich das von Multiplex. Es wird auch alles erkannt.

Die Version der Software ist 1.0.9

[Orthac]

Thanks Frank for your response,
i also think the problem is with the receiver. Can you tell me wich should be the right signal output for the reseiver?

thanks!

[Orthac]

Ich habe jetzt alles versucht. Ich bekomme den Sender auch nicht über Betaflight verbunden...
Ich habe jetzt etwas Geld in die Hand genommen und eine Fernsteuerung und Empfänger von Multiplex bestellt. Ich hoffe, dass dann die Probleme nicht auftauchen.

[FrankS]

It sounds like the output port on the receiver is not correctly configured. On the Flysky website they say the receiver has PWM / PPM / i.bus / s.bus but for some reason Flysky do not any instructions for this receiver online so it not possible to check how the data ports are setup to output the correct format. You could try plugging the data lead into the Ibus port that says Servo, this maybe Sbus out. But while SBus is meant to be an industry standard in practice they are all slightly different so even that may not work.

What Multiplex receiver have you bought, it needs to be at least a DR telemetry type and the light receivers do not have the SXRL output and also to change the BD port on the receiver from Diversity to SXRL mode you will need the USB lead to connect to MPX launcher to make the change.

If you were using Multiplex it would have been better to purchase a Wingstabi with built in MLink so no separate receiver is required, maybe your shop would allow you to exchange the one you have got.

[Orthac]

I bought the "MULTIPLEX RX-6 DR LIGHT 2,4GHZ M-LINK EMPFÄNGER MP" Hope this will do the job. What reseiver do you recommend to use? This hole stuff is driving me crazy... i only want to fly my beautiful plane

[Orthac]

thanks for your research on the Flysky reseiver... Frank

[FrankS]

First off, you don't need a Wingstabi to fly the model, that will just compensate for any wind induced motion, so it will fly smoother. My friend with a Funray just uses a regular receiver and I do the same with my Heron.

Also the Multiplex RX-6 Light can't connect to a Wingstabi, for that you would need a RX-7-DR,https://www.multiplex-rc.de/produkte/55811-empfaenger-rx-7-dr-m-link-2-4-ghz minimum. But rather that use a separate wingstabi and multiplex receiver a better option would be the combined unit https://www.multiplex-rc.de/produkte/55012-wingstabi-rx-7-dr-m-link

What Multiplex transmitter have you got?

[Orthac]

I know that a wingstabi is not needed. But my first flight with the Funray was verry harsch and i almost crashed it. After that i deside to use a wingstabi for easier flight und komfort-functions like autostart.

Ok i will send the wingstabi + the multiplex reseiver back und buy the combined wingstabi. I bought the "MULTIPLEX COCKPIT SX 9 M-LINK sender" hope that will make things easier. I also hope that it´s not to late to send the Flysky sender back to china.

Thanks for you advises!

[FrankS]

The Wingstabi doesn't have autostart or self levelling functions, it is designed to smooth the models flight characteristics and assist in aerobatics. But if you are relatively new to flying it is not going to take over the flight for you.

The Funray by design is very manoeuvrable and responsive, aimed at the experienced modeller. My friends, without any flight stabliser, flies very well.

Cockpit Sx9 transmitter is a very nice transmitter.

[Orthac]

Thats sad... i understood in one video that there is a autstart function on the wingstabi. But yes i knew that the wingstabi is no autlevel device. I am not axactly new in flying but this is for sure my advanced and most expesive model i ever flew. I am verry concerned in flying this model and i am happy about any help i can get