Fahrwerk und Fahrwerk Klappen Sequenzer

[AndreasJ]

I have done the setup in this way.....
i am quite sure you have set the arrow wrong!

Please send me your model data file -> we will check?

Please answer the following question:
Have you checked the arrow setting? behind landing geat in control menu?

-> i tried it with switch <2 , switched landing gear retract out = switch in keyboard direction
(arrow in control menu shows in keyborad direction too)
-> landing gear in, towards antenna direction.

Works all perfect!

[2m1986]

In the next days I will check another time.
I will let you know.

Max.

[2m1986]

Here a short video:

As you see, the sequencer works properly. (the time is a little short).
But when I turn off receiver and transmitter and after I turn on transmitter and receiver, as you see, servos lost the last position...

[2m1986]

I have try this evening with a new program and I have always the same problem:

Turn off receiver, turn off transmitter.
Turn on transmitter, turn on receiver and the servos goes to the other side (like the video).

CH 10 Retract Valve
CH 11-12 Wing gear door
CH 13-14 Tail gear door

Transmitter switch: 1 on the right.
Backward: Gear and Doors down
Forward: Gear and Doors up

PTX021.MDL (3,5 KB)

[AndreasJ]

Thank you for provideing the .mdl file, we will have a look into!

Something i could imagine is, is that you have to adjust the switch point of retract to another value like 0%...
If you switch the profi on, the switch will have pos 0%.... so you have to append this value, that the retracts will be opend by switching on....

Just try -10% or +10%

[2m1986]

Hallo.
On the real program of the model, I don't have switching point.
All servos are assigned with 2 position:
- Retract Gear: -30/+38%
- Wings gear doors: +93/-110%
- Tail gear doors: +99/-100%

On the mdl file that you have now (it's a new program made yesterday evening).... there is all probably assigned with 3 position (+100/0/-100%)
But I don't found any change with it, always same problem.

[2m1986]

Hallo Andreas.
I have tried now to setting the switches to 3 position and change the mid value from 0% to 10 (- or + depends of the rotation of the servos).

There is always the same problem... after to switch off receiver and transmitter, when I switch on, I have the servos that goes in the opposite position.

Have you any ideas?

[AndreasJ]

Dear 2m1986,

the problem seems to be with the slow function, i am sorry to say that, it seems that there are really is a bug ... we will fix it in the next version.

[2m1986]

Hallo Andreas.
Ok, the important thing is that now the problem is identified. (a bit late... but is identified).

Another thing that I don't understand (if you remember I also told to you about that):
On the sequencer, there isn't 12 seconds for close and 12 seconds for open.

If the total sequence goes over 12s with delay and slow, the sequence don't work.
And for my model I need around 14-15 seconds for a complete cycle of close/open.

Max.

[profimc]

Hella, Max!

I want to congratulate you on your insistent patience.
Others would perhaps have given up.
You certainly forced the MPX-team to improve their system.

with regards
profimc

[Reiner]

Hallo Andreas,
wann wird der bug gefixt oder kommt die neue Version?

[2m1986]

Hallo.
After others 3 months, any news about to fix this bug?

Grusse,
Max.

[2m1986]

Hallo.
Today I see the newsletter with the software update 3.56, but on the description I didn't read any news about sequencer....

Is really that's it....???

[2m1986]

Another month is gone...
Now it's the season for the meetings... news for the sequencer??

It born a child in 9 months, it takes the same time for a software update?

[2m1986]

1 JAHRE